Damage evolution around white etching layer during uniaxial loading

Rolling contact fatigue cracks and thermally induced defects are common problems in the railway industry especially as demands for increasing loads, speeds, and safety continue to rise. Often, the two types of defects are found together in the field, however, whether one causes the other to occur is not completely agreed upon. The effect of thermal damage, in the form of a martensite spot on pearlitic steel test bars, on the fatigue life in uniaxial low cycle fatigue experiments was investigated by the authors. However, the focus of the current work was to characterize the damage evolution from the low cycle fatigue (LCF) tests and correlate the crack initiation and propagation with the initial thermal damage. Residual stress measurements, digital image correlation, and X‐ray tomography were used to characterize the effects of the thermal damage before, during, and after fatigue testing, respectively. It was found that the thermal damage causes strain accumulation and crack initiation at the interface between the two materials. The strain evolution was visualized using digital image correlation (DIC), clearly showing the strain concentrations at the top and bottom of the white etching layers (WEL), where the residual stresses are also most tensile. X‐ray tomography confirmed the planar crack growth from the martensite spot.     

新生儿经皮黄疸检测仪的校准

针对经皮黄疸检测仪在使用过程中测量结果无法溯源的问题,通过分析经皮黄疸检测仪的检测原理,研究其测量结果与血清法测胆红素的相关性,提出可尝试采用标准溶液法、标准板法和胆红素浓度模拟法对经皮黄疸检测仪进行校准,并探讨了校准方法的可行性。     

Numerical simulation and experimental research on heat transfer and flow resistance characteristics of asymmetric plate heat exchangers

The asymmetric plate heat exchanger (APHE) has the possibility of achieving balanced pressure drops on both hot and cold sides for situations with unbalanced flow, which may in turn enhance the heat transfer. In this paper, the single-phase water flow and heat transfer of an APHE consisted of two types of plates are numerically (400≤Re≤12000) and experimentally (400≤Re≤ 3400) investigated. The numerical model is verified by the experimental results. Simulations are conducted to study the effects of N, an asymmetric index proposed to describe the geometry of APHEs. The correlations of the Nusselt number and friction factor in the APHEs are determined by taking N and working fluids into account. It is found that an optimal N exists where the pressure drops are balanced and the heat transfer area reaches the minimum. The comparison between heat transfer and flow characteristics of the APHEs and the conventional plate heat exchanger (CPHE) is made under various flow rate ratios of the hot side and the cold side and different allowable pressure drops. The situations under which APHE may perform better are identified based on a comprehensive index Nu/f^1/3.     

基于数据驱动理念的电力日负荷曲线预测方法研究

针对短期日负荷预测的精度问题,本文提出一种基于数据驱动理念的电力负荷预测方法。在建立预测模型前对所给数据采取一定的预处理:首先提取所收集的海量数据的负荷特征,对负荷特征进行分析,然后进行负荷数据与影响负荷值的因素之间的相关性分析,以此确定对负荷影响较密切的因素,随后建立分类器得到各主要影响因素与各负荷类别之间的关系为后续预测模型奠定基础。对预处理后得到的不同类型的负荷数据采用最小二乘支持向量机方法建立不同的负荷预测模型。以南方某发达城市2008年的负荷数据作为算例验证数据,将本文所提负荷预测方法所得结果与未经数据预处理的负荷预测方法所得结果进行比较,结果表明本文提出的方法得到的预测结果精度较传统方法提高约6%。     

水平管内R245fa/R141b沸腾换热特性的实验研究

针对新型混合工质R245fa/R141b，开展水平光滑管(外径10 mm)内工质沸腾换热特性的实验研究，对比纯工质与混合工质的换热性能及4种常用关联式的预测精度。结果表明：纯工质与混合工质的沸腾传热系数均随质量流速和热通量的增加而增大，随饱和压力的增加而减小；随干度的增加，沸腾传热系数均先增大后减小，即存在“过渡干度”，且混合工质的过渡干度大于纯工质；干度小于0.55时，混合工质传热系数小于纯工质；干度大于0.55后，混合工质的传热系数更高；随R245fa质量分数的增加，混合工质的沸腾传热系数增大。在所选关联式中，Gungor-Winterton关联式能准确地预测工质在光滑管内的沸腾换热特性，平均相对误差为16.67%。     

金属基聚合物内衬复合压力容器界面剥离失效及预防

基于构建的裂纹剥离扩展失效过程的模拟方法，提出了预测临界载荷的方法，并通过界面的临界应变能释放率与损伤起始应力，构建了预防界面裂纹剥离扩展失效的等值临界真空压力约束预防控制线和设计准则。结果表明，临界压力载荷受控于界面初始预裂纹长度、复合界面的临界应变能释放率（GIC）和损伤起始应力（T0），与界面初始预裂纹长度呈负关联关系，而与临界应变能释放率与损伤起始应力呈正关联关系；当初始预裂纹长度由11.11 %增至15.55 %时，临界压力载荷（Pc）由87.6 kPa降至为57 kPa，降幅为34.9 %；内衬界面剥离韧性参数（T0，GIC）的坐标点位于等值临界真空压力约束控制线之上，可有效预防内衬界面剥离扩展失效。     

Failure of high power varistor ceramic components

Ceramic varistors are electronic components which have a sharp change (over several orders of magnitude) of their electrical resistance at a well-defined voltage (switching voltage). Starting at low voltages, the resistance is large. But by exceeding the switching voltage the resistance drops dramatically and the component acts as a good conductor. Mounted parallel to a consumer, they are used as protection devices against over voltage loading. In the technical routine yearly billions of varistors are used to protect power lines, transformation stations, electronic devices, microelectronic systems or even LEDs.In service large temperature differences may come into existence, which cause severe mechanical stresses that even may destroy the components. The basic principles of the varistor behaviour are explained and examples of mechanical failure are discussed.     

Investigation of fracture behavior of cement-bonded corundum castables using wedge splitting test and digital image correlation method

To investigate the fracture behavior of cement-bonded corundum castables, various cement contents and pre-treating temperatures have been comparatively studied using the wedge splitting method and the digital image correlation technique. The results show that the microstructure enhances the mechanical properties, so the fracture energy and the maximum load as well as the fracture modes are affected correspondingly. The castables demonstrate the highest fracture energy and maximum load at 1600 °C with cement content of 10 wt% due to an appropriate amount of CA6. At the temperatures of 110 and 1100 °C, the crack propagation within the matrix and along the interface are dominated whereas within the aggregates significantly increased at 1600 °C, leading to the brittleness of materials. However, increasing the cement content can reduce their brittleness, caused by the maximum strain in thex-direction, largest length of the main crack, and high ratio of crack propagation in the matrix.     

R-curves determination of ordinary refractory ceramics assisted by digital image correlation method

As a figure-of-merit, the rising ratio of crack propagation resistance to fracture initiation resistance indicates a reduction of the brittleness and enhances the thermal shock resistance of ordinary refractory ceramics. The significant nonlinear fracture behaviour is related to the development of a fracture process zone (FPZ). The universal dimensionless load–displacement diagram method is applied as a promising graphical method for the determination of R-curves for magnesia refractories showing different brittleness. By applying digital image correlation (DIC) together with the graphical method, the problems arisen with accurate determination of the fracture initiation resistance and the crack length are overcome. Meanwhile, the R-curve is subdivided with respect to the fracture processes, viz the fracture initiation, the development of FPZ and the onset of traction free macro-crack. With the simultaneous crack lengths evaluated from DIC, the contribution of each fracture process to the crack propagation resistance at certain loading stage is quantitatively presented.     

Optimal-correlation-based reconstruction for distributed compressed video sensing

Distributed compressed video sensing (DCVS) is a framework that integrates both compressed sensing and distributed video coding characteristics to achieve a low-complexity video coding. However, how to design an efficient joint reconstruction by leveraging more realistic signal models is still an open challenge. In this paper, we present a novel optimal-correlation-based reconstruction method for compressively sampled videos from multiple measurement vectors. In our method, the sparsity is mainly exploited through inter-signal correlations rather than the traditional frequency transform, wherein the optimization is not only over the signal space to satisfy data consistency but also over all possible linear correlation models to achieve minimum-l₁-norm correlation noise. Additionally, a two-phase Bregman iterative based algorithm is outlined for solving the optimization problem. Simulation results show that our proposal can achieve an improved reconstruction performance in comparison to the conventional approaches, and especially, offer a 0.7–9.9 dB gain in the average PSNR for DCVS.